Engine & Ancilliaries/Gearbox

679 topics in this forum

1. Ignition relay location

   By Multistrada, May 5, 2019
   • 8 replies
   • 644 views
   • 
   • EXCEL V8
   • 37 minutes ago
2. 
   Upgrade today to remove Google ads and support TLF.

3. Problems with starting the engine after filling carb with oil and topping up oil.

   By 77LotusEclat, yesterday at 13:17
   • 3 replies
   • 71 views
   • 
   • EXCEL V8
   • 6 hours ago

4. Earthing Points in the engine bay

   By Grizzly, November 23
   • 4 replies
   • 181 views
   • 
   • Grizzly
   • November 27

5. Newbie Transmission compatibility

   By Markwemple, November 24
   • 4 replies
   • 114 views
   • 
   • Markwemple
   • November 24

6. Engine rebuild sealants etc

   By Benco, November 9
   • 2 replies
   • 447 views
   • 
   • EXCEL V8
   • November 9

7. Gasket between main casing and output shaft housing.

   By Angus553, October 24
   • 0 replies
   • 132 views
   • 
   • Angus553
   • October 24

8. Diff drain plugs; which are compatible?

   By soldave, November 10, 2020
   • 19 replies
   • 836 views
   • 
   • Angus553
   • October 5

9. Elite 501 1980 compression test

   By hatters, September 24
   • 5 replies
   • 274 views
   • 
   • dmottram
   • October 3

10. Decoding Excel Engine Number

    By peteyg, September 29
    • 2 replies
    • 128 views
    • 
    • peteyg
    • September 29

11. Coolant......

    By DELITE, September 26
    • 1 reply
    • 134 views
    • 
    • Rambo
    • September 26

12. Power steering pump bracket....

    By DELITE, September 22
    • 5 replies
    • 150 views
    • 
    • EXCEL V8
    • September 22

13. Electronic ignition

    By Doris the dog, April 27, 2020
    • 6 replies
    • 660 views
    • 
    • DELITE
    • September 20

14. DHLA Spec 5 on 907. Idle jets 50 -> 55 made for terrible idle. Why?

    By BrianK, September 18
    • 3 replies
    • 187 views
    • 
    • BrianK
    • September 19

15. Starting/sparking problems.

    By Angus553, August 6
    • 17 replies
    • 660 views
    • 
    • Angus553
    • September 15

16. Eclat 907 smoking

    By ryandaum, August 29
    • 2 replies
    • 221 views
    • 
    • Drawfiler
    • September 6

17. clutch cable solution ??

    By lil503, December 7, 2020
    • 13 replies
    • 1.4k views
    • 
    • Don.Hasi
    • August 24

18. Getrag 5 Speed - which one?

    By makepeace, May 12
    • 2 replies
    • 383 views
    • 
    • Dunc
    • August 24

19. Flywheel selection

    By Grizzly, June 8
    • 15 replies
    • 402 views
    • 
    • drdoom
    • August 24

20. Overheating

    By Drawfiler, March 4
    • 17 replies
    • 1.1k views
    • 
    • andydclements
    • August 19

21. Cooling fan

    By hatters, August 15
    • 10 replies
    • 357 views
    • 
    • Escape
    • August 18

22. Excel Manifold Replacement - tips & tricks

    By StevoExl, April 4
    • 5 replies
    • 420 views
    • 
    • drdoom
    • August 15

23. Squeak from speedo - cable needs to be lubricated? Best method?

    By BrianK, August 7
    • 2 replies
    • 124 views
    • 
    • EXCEL V8
    • August 8

24. My heater control is stuck on hot. Can I close off the hot supply to the heater in the engine bay,

    By Gray14, August 3
    • 2 replies
    • 206 views
    • 
    • Escape
    • August 4

25. Diff ratio Elite 504 Auto

    By makepeace, July 14
    • 4 replies
    • 268 views
    • 
    • rjwooll
    • July 25

26. BMW Getrag output flange to slip yoke conversion - any ideas?

    By makepeace, July 12
    • 0 replies
    • 130 views
    • 
    • makepeace
    • July 12