free hit
Djs44's Content - Page 3 - The Lotus Forums - Lotus Community Partner #ForTheOwners Jump to content


Full Forum Member (FFM)
  • Posts

  • Joined

  • Last visited

Everything posted by Djs44

  1. Painting fibre glass is probably more difficult than steel ....
  2. HankJPS - do you hillclimb the JPS ?
  3. +1 for Lotusbits - I am having their stainless exhaust on my JPS
  4. Don't know if Turbo tanks are different to nat asp but tanks are nearer £700-800
  5. Front suspension mainly all bolted and torqued up ( as far as you can go without the body on etc ). Washers for top wishbones came from ATZ ( thanks for the link )
  6. Little progress from me on the Esprit . Lull before the storm I hope . I need to get the chassis rolling by the end of the month ( engine etc all in ) so that @changes can have it and fit the body . The engine is still waiting to go on the dyno , everything else is pending that happening ... In the meantime , I've swapped my silver Elise for this beauty Same colour as the one I bought new from the factory in 1999 ( this has a 135 dealer fitted head ) And this is now waiting an engine . Mmmm lots of waiting ...
  7. Body is getting serious - paint straight out of the gun before further work
  8. Yes apparently 1970s Opel Ascona . I have one , so maybe scan and 3d print ? Could also be turned ...
  9. I've checked now and it seems the following are required For each side - 1 off 25mm washer with a serrated side ( or both ? ) and 1 off 40mm washer . Then 2 off the dished washers - the manual suggests 8 off total ( i.e. 4 per side ) but the drawing shows 2 off each side .... these fit on the outside of the wishbones - between the bolt head on one end and the nut on the other . The rubber bush has a serration on one side as per the pic below The 25mm and 40mm washers are both fitted towards the front of the car , no washer between the chassis and the bush at the rear . This seems exactly as Dr Doom's pic shows. I imagine this is quite important to get correct to ensure the correct suspension geometry . Someone had fitted new polybushes to the wishbones ( which have been replaced now with the original spec rubber bushes ) so I basically only have 1 off dished washer and nothing else - so any source for the 25mm , 40mm and dished washers would be great .
  10. Giorgio Thanks for your reply , I’ll check the dims and get back to you 👍
  11. Don’t know why those pics didn’t upload properly
  12. Body really coming on . Can't finish the front suspension until I sort out the dished washers ( which are unobtainable) for the top wishbones . Engine still not been on the dyno but gearbox and rear suspension bits are all ready. IMG_2966.heic IMG_2967.heic IMG_2967.heic
  13. Dr Doom - than you for the pics . I've been studying SOUP's videos on youtube to look at the wishbone pics and they seem quite different washers .. Do you have a washer on both sides of the inner sides of the wishbones ? Minor points but I do want to get this right .
  14. Not sure - the inner side of the bushes has the rubber outside of the metal edge of the bush . I have one dished washer and that doesn't clamp anything ... If they are essential , surely they must be available somewhere ?
  15. Manual is a bit vague on these - I think I need 2 off per wishbone , with the other 2 off being plain . SJ don't do them - do they a) need to be dished and b) if so , any sources ?? I must say the RD Enterprises sheets are a bit more comprehensive than the workshop manual . Thanks
  16. Quick visit to @changes for a body update. Looking lovely .
  17. Thanks Dr Doom . I am using the lower holes. I need some more washers etc before I can proceed. Got some new spring compressors coming for the smaller springs .
  18. Advice please . Is there a certain sequence to assembling the front suspension ? It looks like if I just have the dampers and lower wishbones in place ( i.e. no upright/top wishbone etc ) the lower wishbone will be in contact with the chassis . The springs ( 2.5inch) are a bugger to compress . Also what is this part ? Thanks in advance.
  19. Hope you are going to clean it before the weekend 😜
  20. Mike has some spares , so we will swap it I think .
  21. Went to see @changes on Saturday - a couple of pics of where he's got to . I really admire both his attention to detail and also his complete dedication to doing the best job possible. Quality takes time. I also collected all the front suspension components - unfortunately I forgot to get a few bolts plated so I can't start the build yet - also took the front hubs to get them cleaned up. The gearbox has been stripped down and the casings vapour blasted - this revealed a slight problem with the top - see pics , which is cracked. Gearbox was generally very good but needs a new input shaft and output bearings. Should have the engine and gearbox back in 3 weeks so I can start to rebuild the rear end.
  22. I'm going on the 12th - will say hello
  23. Djs44

    JPS Info

    You can get the decals etc - I know SJ Sportscars does them .
  • Create New...