Web
Analytics Made Easy - Statcounter
C43 - The Lotus Forums - Official Lotus Community Partner Jump to content


C43

Basic Account
  • Posts

    307
  • Joined

  • Last visited

1 Follower

About C43

  • Birthday 12/11/1965

More Info

  • Name
    Christian
  • Car
    Evora NA, Esprit S2 WC, Esprit S3 Turbo 1984
  • Modifications
    2bular exhaust. ICE upgrade speakers, amp, sub. Diamond cut alloys.
  • Location
    oxfordshire

Recent Profile Visitors

4,082 profile views

C43's Achievements

Newbie

Newbie (1/14)

55

Reputation

  1. part 50 was what I changed. The catch on my old one was completely worn out of shape.
  2. Hi I had much the same problem on my 84 turbo. I got it adjusted to the stage where it would not pop open over a bump but I did have to slam it quite hard to shut it. Anyway I finally bit the bullet and bought a new rod with the catches (the bar that runs across the inside of the boot) and it is much better now. The catches on my old rod were worn to the stage where they did not latch properly any more, the new one is quite a different profile and holds onto the boot much better. cheers C43
  3. Hi does anyone have any experience on changing rear toe shims and how much effect it has on the rear toe. From the geometry it looks like 1mm of toe shim is equivalent to just under 0.7mm of toe change. Just checking if anyone has found this in practice? thanks C43
  4. Ditto, mine are fully refurbished with braided hoses front and rear and new fluid and everything rebuilt, and I agree they are not great. Its an old car so not surprising but given the acceleration I do have to remind myself that the brakes will not be as good as say the Evora I used to have.
  5. FYI on my turbo when I compression test it cold I got 10 / 10 / 9.8 / 10. All in bar. This is a rebuilt engine. I guess its the spread rather than the absolute numbers you are looking at.
  6. Might be worth giving it another bleed. I also have an 84 turbo and after a complete rebuild I had to bleed it a couple of times to get the pedal back. I also find heel and toe difficult due to pedal positioning (even with a stiff brake pedal) but have mastered it after some driving.
  7. Hi, I have one spare thats bent to shape, PM me if your interested.
  8. yes I did and made them up, looks good. I may have a spare, will let you know.
  9. haha,. I found a place in wales which does exactly the right size and pattern but only in stainless steel not aluminium. The stainless will last better but obviously heavier which is upsetting me a bit! https://www.themeshcompany.com/products/-6-Mesh---3.33mm-Aperture---0.9mm-Wire-Diameter---SS304-Grade----Woven-Wire-Mesh--56.html#SID=59
  10. Hi I am just refurbishing the engine cover on my 84 turbo and would like to replace the wire mesh on the center. Has anyone found a good place to buy the original spec? thanks C43
  11. I put my sub on the lhs under the panel that goes around the window on the lhs on the engine. That way its close to the battery so power is easy to get to it. Otherwise I would go through the speaker hole in the rear bulkhead, again on the lhs. This is how I ran my pre outs to the sub and the speaker cables back. I have now done away with pre outs and have connected a bluetooth direct to the amp and drive it of my phone.
  12. know what you mean by glamorous assistant! BTW if your rotate around the top mount you tend to open up the gap at the front of the door, if you rotate around the bottom mount you tend to close up the gap at the front of the door. Looking at the geometry I did not think it would make much difference but in practice I found this a useful way of adjusting both the height of the door and both the for / aft movement of the door. Useful if you are being anal about getting your shut lines good (better!). Which your rotate around depends on how much you undo the bolts holding the top and bottom hinge points. The one you are rotating around you undo less. So if I wanted to open up the gap on the leading edge then I would undo the top bolt by 1/2 turn and the bottom bolt by 1 turn (having first taken the weight with my jack) then jack the door up a little and retighten. BTW the absolute number of turns to undo the bolts by are by memory from my car, yours might be different. Let me know if this is not clear. cheers C43
  13. I held the door up with a car jack at the end and measured the distance to the ground, I found it easier to accurately adjust the height when open that way. I took the weight off the door hinges with the jack then undid the hinge bolts inside the body a bit then lifted the end of the door with the jack then did the door back up. If you open the door and lift the end up and down and feel inside the hinge mechanism you should be able to feel if there is any play and hence if the bushes have worn. Even if your hinge bush has worn rather than the nut plate sliding I guess you can still lift the door a bit with the hinge mounting bolts rather than changing the bush itself. good luck C43
  14. is there up and down play in the door hinges. If so then the normal cause if the plastic door bushes have worn out. Bit of an epic to change. I have done it a few times now and I would still recon on a full day to do one.
×
×
  • Create New...

Important Information

We use cookies to enhance your browsing experience, serve personalized ads or content, and analyze our traffic. By clicking " I Accept ", you consent to our use of cookies. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.