free hit
Fixing Evora flat battery and boot release cable problems - Page 2 - Engine & Ancilliaries/Gearbox - The Lotus Forums - Lotus Community Partner #ForTheOwners Jump to content


Fixing Evora flat battery and boot release cable problems

Recommended Posts

Great description and discussion. I threw my phone in the boot without removing the cover, but can still see that I would probably benefit from the same “+2 washers” tweak to move the hammer out a couple of mm...


Link to comment
Share on other sites

Upgrade today to remove Google ads and support TLF.

Glad people are finding this handy👍🏼
Mik, I can see the wear mark on your hammer just on the corner, where it is just catching your latch pin. Does your manual cable work okay? My whole issue was that that the manual cable tilted the mechanism (because it is attached to a higher point of the hammer lever) and the hammer slipped behind the latch pin.

Out of interest, how many washers do you currently have per mounting bolt?

And remember, if you do adjust it, make sure everything is aligned correctly and bolts tightened before you shut your boot (and the key is in your hand😳). Otherwise you could cause a bigger problem than you already have. 
There is that old saying: If it ain’t broke, don’t try to fix it😀👍🏼

Link to comment
Share on other sites

  • 5 weeks later...

Okay, time for an update.

I now need to rig up a method of trickle charging the new battery. The car is in a garage with NO mains power, so I am going to use a solar panel setup on the roof...more on that later.

First step is installing a Magcode connector on the outside of the car. I want to use this method as I don’t like the idea of having a cable being kinked in the boot lid (even though other people say there’s enough clearance in the rubber seal), I also have a car cover on most of the time, so don’t want that trapping the cable against the bodywork.

So I read Chad’s (2011 chrome orange) excellent post on Lotustalk with interest and considered buying the kit he used from Hethelsport

But it’s fairly expensive plus import duties to the U.K. So I put my own kit together...

The Magcode connector is available on Amazon for £36.99

The protective cover is £11.99

Then a few bits of heat proof cable, some protective braiding, a fuse carrier and some crimp connectors all for about a tenner. So I had my kit for about £60.



Next step was finding a route from the battery compartment to where I’m mounting the Magcode in the diffuser at the left rear of the car.

On the S1 Evora there is no vent under the carpet like Chad has on his later model, but the battery vent pipe goes through a grommet and pre-drilled hole into the left rear wheel arch, it then dangles down into fresh air near the ARB and diffuser assembly.



Perfect, I can use this route. I considered just removing the vent pipe to make way for my cabling, as I always thought vent pipes under a ventilated bonnet i.e. on a front engined car were a waste of time. But in an enclosed compartment in the boot of the Evora I think it’s pretty important to allow hydrogen to escape. My car didn’t have it’s vent pipe connected as the little vent elbow was missing (previous owner🙄), so I got a new elbow and put that right👍🏼.

I decided to drill the hole for the Magcode in the aluminium diffuser just to the left of the exhaust hanger mounting bracket. It’s shielded from the heat of the exhaust here and easily accessible to hook up to my solar panel charger.

So the diffuser came off to make drilling easier and safer. I clamped a block of wood to it to support drilling the hole and stop the aluminium flexing or getting damaged when the hole saw breaks through. Here I am at the point of no return with a 29mm hole saw...measure twice cut once!🙂




Edited by Bulletmagnet
Link to comment
Share on other sites

I installed the Magcode with about a foot of spare cable. This allows the diffuser to be dropped and the connectors easily removed (just got to remember to tell that to any mechanics working on the car in future). It’s then routed up through a hole in the chassis structure, where the slack foot of cable neatly stows, then up into the left rear wheel arch.

I protected the cables with the braiding and put some heat shrink sleeves on the ends to neaten it up.


Then in through the grommet to the battery compartment where I connected my fuse carrier and hooked it all up to the battery. No need for the braiding in here...I couldn’t get it through the grommet anyway.


Link to comment
Share on other sites

So this how it looks with the diffuser back in place:


And here it is with the cable from my solar charger connected:


The great thing about this connector is the simplicity of it. It only lines up in one place so you can’t do it wrong, which is great as you can pop it on without having to get down on your hands and knees...AND the magnet actually switches it on inside the plug so it’s essentially dead when disconnected.👍🏼

Next post will be some solar panel fun, which hopefully will be useful for anyone away from the mains like me...

  • Like 1
Link to comment
Share on other sites

  • 2 months later...

Any tips or mods for someone like me running a lithium battery in a 410? Would I have to step the power up to mains and then plug a Lithium compatible charger into it? 



Link to comment
Share on other sites

Should just be able to use a different charge controller suitable for lithium batteries. 

eg this one might be suitable:

Link to comment
Share on other sites

On 10/05/2020 at 12:07, MJ said:

Any tips or mods for someone like me running a lithium battery in a 410? Would I have to step the power up to mains and then plug a Lithium compatible charger into it? 

I can’t advise personally as I’m no expert, but give the chaps at Photonic Universe a bell...they were friendly and knowledgeable, so should be able to help. Happy customer here 👍

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Create New...