free hit
counters
Just a little slip on the ice.... 1996 Esprit V8 rebuild - Esprit 'Project & Restoration' Room - The Lotus Forums Jump to content
davidw

Just a little slip on the ice.... 1996 Esprit V8 rebuild

Recommended Posts

Start.thumb.jpg.a7e5449b3bbd2653f7b6dc61d53a76cc.jpg

As you can see from the photo, even a small drift into a soft verge does more damage than you’d expect. In my case, the left oil cooler is broken, so that stopped me using the car. The radiator tray was damaged as well.

Also obvious is that the paintwork was in a pretty shabby condition. The little bump gave me an excuse to deal with the problem of the paintwork as a whole.

So after the insurance negotiations were complete, it was time to decide who should do the rebuild work. This was an easy decision, because Specialised Paintwork in Reading, were going to allow me to do most of the work myself on their premises. Whilst they did the prep and paint, I would do the break-down and re-assembly. Fun!!

 

At the same time, I took the opportunity to make a number of improvements and changes to the car.

 

start_2.jpg

After the accident happened in January 2017, work started mid-March, and the complete strip of the outer bodywork took 6 weeks.

Body_001.jpg

  • Like 1
  • Sad 2

Share this post


Link to post
Share on other sites

Upgrade today to remove Google ads and support TLF.

Previous photo is the damage to the front after the lower spoiler and bumper have been stripped off.

After 20 years, there is plenty of rust to remove. Here is the exhaust bracket and rear bumper bracket, and a hole in the heat shielding.

 

Body_002.jpg

Here is the NS rear wheel arch extension after removal. The embedded attachment bolts are always fully rusted, and stay in the holes when you pull off the arches. It’s an odd way of doing it and despite meticulous measurements, it is very difficult to glue in new attachment bolts onto the arch and get them in the right place… trial and error was my method.

 

Body_003.jpg

Radiator tray after removal showing damage to one of the A/C condensers. Fortunately the radiator itself survived.

 

Body_004.jpg

  • Like 2

Share this post


Link to post
Share on other sites

Here are some images of under the nose once the radiator tray has been removed.

 

DSC04269.jpg

DSC04270.jpg

DSC04272.jpg

This shows the danger of ignoring a leak in the boot. One of the drains for the lip around the edge of the tailgate had broken away in the bottom of the boot and been ignored. After several years, these internal exhaust brackets had turned to dust. Fortunately Lotus still had them available at the time.

Body_005.jpg

Here is the LH door being stripped, and the protection bar left after the shell has been removed. It was a great idea to hang the shell and window frame off the bar. It gives the impression that the frame would be easy to re-fit into the correct position, but I found that there wasn’t quite enough freedom of movement to achieve this. We decided to remove the door shells because the metal strip holding the window seal along the top of the shell had long since rusted, and needed to be removed. There are a lot of parts to remove from the shell, and once prepped and painted, it takes a very long time to get them all back together so that the door shuts correctly. In fact, after many hours of fiddling I was never quite satisfied that they did shut exactly.

DSC04280.jpg

DSC04282.jpg

DSC04288.jpg

DSC04296.jpg

DSC04297.jpg

Body_006.jpg

The headlight recess collects dirt and water and was always half full. You can see how small the drain hole is here. This was a great opportunity to make the drain hole much bigger and stop the headlights sitting in water. The pod pivots were replaced also.

Body_007.jpg

The most unexpected part of the rebuild was losing the interior. Once the headlining material had to be stripped away, it collapsed into dust – no more interior. The rebuild suddenly became much more involved than originally intended. (Where have we all heard that before?)

Body_008.jpg

Share this post


Link to post
Share on other sites

Progress with the accident repair. It was clear that the shell had not twisted or warped, so a simple repair of the cracks was all that was necessary.

Body_009.jpg

Body_010.jpg

The top of the A pillar is an easy place for the body shell to crack.

Body_011.jpg

All the jacking points had cracked – the body not nearly strong enough in those areas.

Body_013.jpg

Here’s the body after the accident damage has been completed and primed.

Body_014.jpg

Now ready for the primer layer.

Body_015.jpg

Body_017.jpg

Body_021.jpg

Body_022.jpg

Body_023.jpg

Body_024.jpg

I don’t know why I didn’t notice how awful the colour of the carpet was!

Body_018.jpg

The painter made up a rig for painting the new rear spoiler. This turned out to be a major task due to the poor quality of the part. The two halves of the spoiler were not sufficiently joined and had cracks along the joint. It took 2 days to fully correct the problem – very expensive!!

Body_025.jpg

Body_026.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Good work!

It'll be a brilliant looking and performing car.

Cheers,

Jacques


Nobody does it better - than Lotus ;)

Share this post


Link to post
Share on other sites

LH door beam back in place ready to accept the door shell.

Body_061.jpg

LH door completed. Expect to spend a few hours setting its position, go away, have lunch, then come back and decide to do it all over again…

Body_062.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Quality of the work looks good.

Did you repair or replace the bumper and lower valance?

Share this post


Link to post
Share on other sites

RH door being assembled. Naturally the 2 doors needed completely different settings to align them into position.

Body_063.jpg

Body_064.jpg

Inside the RH door showing the beam, and the frame mounting bolts. Attaching the wing mirror is easier than you might expect.

Body_065.jpg

Body_066.jpg

Here is the new exhaust bracket added after a new strip of heat reflecting layer has been applied.

Body_067.jpg

And with the heat shield in place.

Body_068.jpg

  • Like 1

Share this post


Link to post
Share on other sites
4 minutes ago, tomcattom said:

Quality of the work looks good.

Did you repair or replace the bumper and lower valance?

We sourced a second hand bumper and a new lower valance, if I remember correctly.

Under the nose also with a new layer of heat reflecting insulation applied.

Body_069.jpg

New radiator tray ready to go in with new condenser and pipes.

Body_070.jpg

Headlight recess with enlarged drain hole ready for its pod.

Body_074.jpg

LH oil cooler in position.

Body_075.jpg

Share this post


Link to post
Share on other sites

Here the shot blasted and powder coated mounting brackets are being riveted back onto the front bumper. Replacing the front bumper should be straightforward, however, attaching the nuts in the corners is perhaps the most difficult access imaginable. I even bought a special tool from Snap-On to assist me; my small hands are too big to squeeze down the gap to reach the bolt shaft and turn the nut…

It’s at moments like these that you get to find out the true nature of the build quality of the car – terrible!! This is a second hand original bumper in moulded plastic (replacement ones are glass fibre) and matched the new lower spoiler that was available also in moulded plastic. The pilot holes for the rivets are not in identical places, showing that no two parts are manufactured the same…

Body_076.jpg

Body_077.jpg

Body_078.jpg

The original leather dash covering was a mid-grey that reflected badly in the windscreen. I took the opportunity to remove the windscreen so that I could replace the leather with black Alcantara.

Body_079.jpg

New inner exhaust brackets back in place and being covered in the original carpet.

Body_080.jpg

I noticed that the fuel cross feed pipe was looking very degraded and removing it was the only option. What a fun way to spend a couple of hours trying to empty both tanks whilst having a bath in 97 octane petrol… Dismantling it revealed rust on the metal pipe, fungal growth on the flexible hoses and collapsed baffles on the sides of the fuel tank cells. So a shot blast and paint of the metal pipe, new hoses and baffles were put in place.

Engine_002.jpg

Engine_004.jpg

Engine_005.jpg

New tailgate drain tube sealed in place.

Body_081.jpg

Radiator tray back in place with three new fans.

Body_082.jpg

Share this post


Link to post
Share on other sites

Resprayed rear valence aerofoil back in place.

Body_083.jpg

Front bumper in place.Body_084.thumb.jpg.9174a9f19d88f78b358c97d3044660c6.jpg

Lower front valence receiving new grills.

Body_085.jpg

Body_086.jpg

Lower valence in place and fitting the oil cooler tunnels.

Body_087.jpg

Body_088.jpg

Share this post


Link to post
Share on other sites
12 minutes ago, davidw said:

Under the nose also with a new layer of heat reflecting insulation applied.

Body_069.jpg

What did you use and where did you get it from? I've got the rad out of mine at present and the insulation is on my to-do list.

Share this post


Link to post
Share on other sites

Fitting the fog lamps. These are Saab parts. You can also see the new air tunnel to feed air to the radiator.

Body_093.jpg

Body_094.jpg

3 minutes ago, tomcattom said:

What did you use and where did you get it from? I've got the rad out of mine at present and the insulation is on my to-do list.

I'll dig out the details and get back to you on that, Tom.

Fitting the underpanels. Needless to say, lots of fettling was required to make everything fit, even though the front lower valance is a new part.

Body_098.jpg

Body_099.jpg

Body_095.jpg

Body_096.jpg

Body_097.jpg

Fog lamps from the front – wonderful fit! Again with lots of adjustment to get the position anywhere near acceptable.

Body_100.jpg

Body_101.jpg

Share this post


Link to post
Share on other sites

One of the last things to do was fitting the front spoiler lip. These were looking tired and it was suggested to replace them with an SJ sourced straight lip. But I like the odd shaped ones, they somehow seem to suit the car. The paintshop has a Wurth product that you apply after sanding the rubber. They came up perfectly afterwards! Well worth the small effort.

BODY_101c.jpg

You might have noticed that I didn’t mention the bonnet or boot lids. These were straightforward, and didn’t present me with any problems. I did have to replace the grills on the bootlid over the engine, and there is a question over the rigidity of the rear spoiler – the nuts and bolts holding it in place does not inspire confidence.

We also decided to add some extra protection to the sills where the hydraulic ramp pick up points are. After those locations were repaired and painted, we fitted aluminium blocks 40x40x25mm, screwed and glued to the body work. This keeps the ramp pads off the bodywork. I would fix the issue of the spare wheel scissor jack much later on.

 

Final stage – fitting the new set of AWI wheels. I have always preferred these, so it was fabulous to find a set at SWLC!! Needless to say I now have a spare set of OZ Futura wheels if anyone is interested, and the original low level rear spoiler is also available.

Body_102.jpg

Body_103.jpg

One of the great things about having a proper garage to work in is the hydraulic lift. I took the opportunity to do some other remedial work on the engine. The alternator had stopped working, so that came out, and the air con compressor had never worked. So I bought a new compressor and took the alternator to a local guy who refurbs them. It was good to find out that both these items can be extracted and fitted with the engine in place. I didn’t even have to lift one side of the engine off its mount. I did have a problem with the cable electrical plug for the compressor. Mine had obviously been damaged before and the connector broken off. There was a makeshift press-on sort of connector which didn’t actually work. The connector looked standard but isn’t, and I found an alternative in Australia, which still needed a little fettling to fit properly.

  • Love 1

Share this post


Link to post
Share on other sites
11 hours ago, tomcattom said:

What did you use and where did you get it from? I've got the rad out of mine at present and the insulation is on my to-do list.

Search Thermal Velocity on here.

  • Thanks 1

Margate Exotics.

Share this post


Link to post
Share on other sites

@davidw I assume that you'd recommend Specialised Paintwork? They know what they're doing with GRP bodies?

I'll need to get my Turbo Esprit painted at some point (eventually) and Reading isn't too far from me...


Not worth starting anything now...🍺

Share this post


Link to post
Share on other sites

Neil, The Beaconsfield Workshop are also amazing with fibreglass cars, a lot of Lotus dealers and TLF members have used them and they're a TLF sponsor so might do you a deal as an FFM :thumbup:


88 Esprit NA, 89 Esprit Turbo SE, Evora, Evora S, Evora IPS, Evora S IPS, Evora S IPS SR, Evora 400, Elise S1, Elise S1 111s, Evora GT410 Sport

Evora NA

For forum issues, please contact the Moderators. I will aim to respond to emails/PM's Mon-Fri 9-6 GMT. 

Share this post


Link to post
Share on other sites

Cheers Bibs. TBH I'm a while away from paintwork yet (!) but it's good to have the names of some recommended places for when I'm ready.

  • Like 1

Not worth starting anything now...🍺

Share this post


Link to post
Share on other sites

Share this post


Link to post
Share on other sites
On 03/05/2020 at 19:43, tomcattom said:

What did you use and where did you get it from? I've got the rad out of mine at present and the insulation is on my to-do list.

Hi Tom,

I found 3 sites for what looked like suitable alternatives. Something on Amazon called GlassMAT High Temperature Reflective Engine Bay Thermal Acoustic Insulation Sound Proofing Foam, there were also several options at www.agriemach.com/c7-heat-and-sound-insulation, and also there was this at CBS, www.carbuilder.com/uk/heatmat-reflective-insulation. I used the CBS product.

 

  • Thanks 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...