free hit
counters
Oil cooler replacement, saved a few quid - Engine/Ancilliaries - The Lotus Forums Jump to content
Sign in to follow this  
ajheath

Oil cooler replacement, saved a few quid

Recommended Posts

A couple of weeks ago one of the oil coolers gave up, which I caught before I lost all the oil and more serious damage could have been done.  Now for those that don't know these can be a right bugger to change for a couple of reasons, first getting at them, especially the top union on the drivers side in a Delco brake equipped car, and secondly steel unions on ally fittings, not to mention the retaining bolt which in typical Lotus fashion will probably be very corroded and snap off with the first tun of the spanner, which mine did.

After very carefully moving some of the ABS kit to get access to the top union and managing to get a 30mm spanner on it rather than the union undoing the threaded part just snapped off the oil cooler leaving it inside the union of the cross over pipe, unsurprisingly the same happened with the bottom union.

Obviously this then presents a problem, how to get the broken bits out of the unions on the oil supply pipes, or face the expensive option of replacing the entire supply pipe, and in the case of the cross over pipe that goes through the front boot the very real need to replace the other oil cooler too!  After a chat with Dave "Changes"  he said the best route with the bottom union was to just cut off the hose as close to the union as possible then just get a replacement union from Hydrafit in Wolverhampton.  There then should be just enough hose to remake the joint using double Jubilee clips to seal it.  A trip to Haydrafit in Walsall St Wolverhampton on Friday saw me leaving there with the exact same 5/8 elbow as fitted to the hose originally and 4 high quality Jubilee's for the princely sum of £8.50, far cheaper than the £120 for a new hose from a Lotus specialist.  If you did need an entire new hose they could make one up for you with the correct fittings and proper swaged ends for a fraction on the cost of a Lotus replacement, worth bearing in mind.

The top union presented more of a problem.  Fist option was to try and get the fitting out of the union with a couple of large spanners, but to no avail as I just couldn't get enough purchase without a vice, so the only other option was to get the hose off the metal transfer pipe.  Problem with this is that the hose is swaged on to the pipe with a very substantial fitting, which I attacked vey carefully with a Dremel fitting with a small grinding wheel cutting it along its length on two sides to split it open being careful not to damage the pipe.  Then it was a fairly simple job to get the broken fitting out of the union  on the bench in a vice.  Like the bottom hose there was enough slack to reattach the hose to the pipe with a couple of Jubilee clips.  

All fittings have been liberally coated with copper slip and a nice new stainless M10 bolt used to secure the cooler to the body.  

Below are a couple of shots of the knackered cooler in situ and the new cooler and all the bits to refit it.

Thanks to Dave for his sage advice which potentially saved me a small fortune.

 

file_zps95532f6a.jpg

leaky knackered cooler in situ once the ducting and under tray have been removed

 

file_zpscccf7099.jpg

New Setrab cooler and fittings prior to refitting 

Edited by gasmangt3

Share this post


Link to post
Share on other sites

Upgrade today to remove Google ads and support TLF.

Ade, ive got a spare set of oil cooler pipes if you had ended up needing them. And I have a man who can make them up as per originals for a seriously lower price than the originals too..if anyone else is in need!

Share this post


Link to post
Share on other sites

i had an oil coller burst a while a go. and teh alloy connector snapped so i used some caustic soda with watr in a jam jar, left the pipe in for a few hours and no alloy left. only a couple of pounds from boots the chemist.

Share this post


Link to post
Share on other sites

I tried that Pete, as I use caustic to strip paint from model cars but no joy

Share this post


Link to post
Share on other sites

Worked fine for mine. I did change it once and i used a full jar and not too much water the jar got red hot.

Share this post


Link to post
Share on other sites

Worked for me as well, first time not really but the second attempt I upped the concentration and a couple of hours later clean couplings without aluminium bits.

 

Freek

Share this post


Link to post
Share on other sites

I replaced my o/s cooler last year, leaked in the bad winter last year. Ended up also replacing the pipe from the cooler to the engine with the help from Andy Clements, definitely a two man job. I did spend four hours though dremelling the alloy thread out of the front cross pipe union to save it, which worked. I did dremel the pipe from the cooler to the engine, but it couldn't be saved. I got all my parts from SJ.

 

Like what's been mentioned, I had to purchase a set of crows feet spanners to do the upper nut up. All in all it was a massive job for such a small item, especially undoing the cable ties in the tunnel, for Lotus, easy when there is no body sitting on the chassis on the production line installing, not so easy with a body on the chassis. The simple answer for Lotus would have been to add a steel intermediate adaptor between the cooler and the pipes. This way you have steel on steel and when the thread shears off in the adaptor you just replace those parts. I suppose weight and the cost of fitting four to every car would have sent the figures two high, cost and weight!  :)

 

Here are pictures of my fitting

 

http://www.flickr.com/photos/owengt3/sets/72157629389193265/

Edited by OwenGT3

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  


×