free hit
counters
Clutch Issues - Gearchange/Gearbox/Clutch - The Lotus Forums Jump to content
Sign in to follow this  
rogerch

Clutch Issues

Recommended Posts

Long story short I think I'm up for a new clutch. The adjuster is frozen/rusted solid, I'm uneasy about swinging on it harder, the fork goes next and I'm buggered.

Question, if I could move it, should I ? It seems preset, play with it at your own risk and maybe damage the flywheel, if it gets down to the rivets.

Advice, (Mr Clark)

If I do get a new clutch over I'll replace the adjuster too.


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

Upgrade today to remove Google ads and support TLF.

The clutch is designed to start slipping before it gets to the rivets.  If you adjust it, then it is possible to wear past the rivets...

 

Change the clutch when it starts slipping.  I also change the pressure plate and throw-out bearing.


Travis

Vulcan Grey 89SE

My Lotus Photo and Projects Album

Share this post


Link to post
Share on other sites

No point adjusting that if it's to spec.  As Travis says, you'll just feel pain later.  And yes, change the lot.


British Ambassador to Florida, New York, Denmark and Newfoundland.  And Sweden.

Share this post


Link to post
Share on other sites

Naturally I'd do the lot, hate doing things twice. (postage to OZ is a bit hefty)

One thing I would like to know, the size of the punches to to knock the drive-shaft pins out ?


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

After the problems Justin had with the pins, i would suggest you speak with Sparky about his method of removing the drive shafts at the spider yokes at the gearbox end instead. I'm not sure how that works, but hopefully we are about to get a description here :turned:

 

I guess if you're about to do the clutch, I wonlt be far behind you as I seem to trail you by 3 months on everything. Take lots of pics.


Too many Toys are never enough !

Share this post


Link to post
Share on other sites

Undo the gaiter, mark spider and yoke position, pull it out (suspension arm bolts removed of course).  Takes all of 90 seconds compared to the aggro of knocking the pins out.


British Ambassador to Florida, New York, Denmark and Newfoundland.  And Sweden.

Share this post


Link to post
Share on other sites

You're up early,  :D

 

I wanna take the pins out,  :sofa:

 

But another quick one, can I take the box out from underneath, is it possible, practical, ?? spinal issues means underneath would be much easier for me.


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

You're mad.

The box will come out (just) down on the right. spinally though, I think it'll hurt either way!

Up early?? I overslept today!


British Ambassador to Florida, New York, Denmark and Newfoundland.  And Sweden.

Share this post


Link to post
Share on other sites

I've measured the adjuster as per manual, 12.5mm (Renault box). But mine isn't 12.5mm

From tip to the arm is 13.04mm, the lock nut is already off so subtract 7.7 for that and end up with 5.34 a substantial difference.

So suspicion is, someone already adjusted it, but I've had it 5 years !

So I guess I need to stop procrastinating and order a new clutch kit, a new adjuster too !

Edited by Roger the Dodger

Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

and a mechanic


Amateurs built the Ark

Professionals built the Titanic

"I haven't ridden in cars pulled by cows before" "Bullocks, Mr.Belcher" "No, I haven't, honestly"

Share this post


Link to post
Share on other sites

And a spring

What's this spring Peter ?


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

The clutch fork spring. Only a few quid. If you doing the clutch change it. Its held on with x1 rivet its a sprung piece of steel not a coil spring. If this goes its box off again so do it while you are there
 

here's a couple of pics from when i did my clutch.

97f8ef7f_zpse898e8e6.jpg

ee1c685b_zps4ae8d95b.jpg

Edited by mr.oogieboogie

It's Oogies turn to boogie

Share this post


Link to post
Share on other sites

Had a nice chat with Steve at SJ last night, lunch time UK. New clutch kit, adjuster, lock nut, and new roller pins all on it's way.

Peter I'll pay special attention to that spring when I get it all apart.

I've also just ordered a 3/8 air ratchet wrench, wanted one for a while, make life a bit easier on the old sole.


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

Well the clutch kit has just left Heathrow, thanks Steve. According to the shipping details I live in "Outlying Areas-NSW"  :shock:

 

My new air ratchet should arrive tomorrow, and I've just bought locally a set of pin punches, so I reckon I'm ready to go. 


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

I think you're right Travis, I had a look today, and I think it will be much easier to get out top side rather than underside. As I have access to a hoist, I think that's the way I will go.


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

Well wouldn't yer know it !

I got the hoist out today (Stored dismantled under the bench in the corner) Put my back out doing it ! So to save my back I get the hoist out and stuff my back doing it. May as well just settled for picking up the gearbox in the first place !

I'm thinking I'll give it a good clean while it's out, maybe even a nice coat of silver enamel, look nice stay clean.

Whether the clutch is here or not (Stuck in Sydney Customs for 48 hrs) I'm starting Monday afternoon.


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

You certainly did Peter, I'll be paying close attention to it when I get it out.

The clutch is here, was on my doorstep when I returned from seeing the specialist today.

 

I should have started already but after a morning of pushing prodding, and "Is that painful ?" as I climb down off the ceiling ! I had a rest instead,   :doc:


Life is like a sewer, what you get out of it, depends on what you put into it. (Tom Leahrer)

Share this post


Link to post
Share on other sites

Don't forget the spring.


British Ambassador to Florida, New York, Denmark and Newfoundland.  And Sweden.

Share this post


Link to post
Share on other sites

I feel for you Roger. My spine goes into spasm far too often, although it could be much worse such as skeletal rather than muscular.

A problem I had for several years that was finally sorted by a small operation, abscess on the coccyx, has seemingly returned. Looks like I'll be having a trip back to the hospital, either that or getting to know a rather large needle.

Share this post


Link to post
Share on other sites

I have a spinal graft on my lower back, did it when I was 13. they had to fuse the vertabre with bone from my hip. Fortunetly been good ever since.


Amateurs built the Ark

Professionals built the Titanic

"I haven't ridden in cars pulled by cows before" "Bullocks, Mr.Belcher" "No, I haven't, honestly"

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...