dixi4uk 65 Report post Posted March 15, 2015 After reading this firsthand experience I would suggest that 100w bulbs may not be a good idea afterall. Technology has in deed moved on with the latest type of super white standard wattage bulbs being just as bright if not brighter. Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 15, 2015 I suspect your "bobbins" have fallen off. On my first eclat ( a 76) there were nuts bonded onto the inside of the door' but when I came to change the mirror, they fell off inside the door. It is possible to reach inside to hold a nut when the door card is off, but it is a bee-ach of a job.... I will certainly investigate further regarding the bobbins. Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 19, 2015 Decided to add a rear window blind, so I've been busy constructing one, quite fiddly but I'm loving the end result, very retro and adds a little bit of privacy to the rear hatch. 1 Quote Share this post Link to post Share on other sites
Dunc 377 4 Vehicles Report post Posted March 19, 2015 Do you have a labrador charlie? NB on the elite and eclat the headlight feed is via a relay (at least it is on mine...). The current doesn't run directly through the switch to the lights. D 2 Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 19, 2015 Haha, no labrador. So to upgrade to H4 shouldn't be a problem? I remember when I had the esprit I changed the bulbs and burnt the switch out, pain in the arse and a relatively expensive fix. Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 19, 2015 The blind idea looks good. Something quite different, I just love the way you think outside the box. Have you considered tinting film on the glass?. I have a non tinted car that has a tinted replacement screen. I have decided to go this route with a very pale tint. This mainly because all the glass has to come out any way. The doors for instance need stripping to do the hinge pins, the rear quarter glasses are falling out of their own accord. That only leaves the tailgate insitu. 1 Quote Share this post Link to post Share on other sites
Denis247 24 Report post Posted March 20, 2015 I think you've lost the plot re those blinds. 1 Quote Share this post Link to post Share on other sites
Fueltheburn 85 4 Vehicles Report post Posted March 20, 2015 I quite like the blinds... Reminds me of a De-lorean rear window I saw a while back... Just looks very different and adds an interesting touch. 1 Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 20, 2015 They're nothing new, they've been around for years, the vdub scene love them. I just wanted something to help hide all the shit that I keep in the boot! They tend to be light colours but I wanted mine to be fairly unobtrusive. Quote Share this post Link to post Share on other sites
clivef38 152 Report post Posted March 20, 2015 Hi Charlie. I know its along trip from Turin but is there any chance of seeing the Panther at Duxford on May 3rd. So far over 30 Loti going. See events. I have an Elite with MX5 headlight conversion that does not need welding skills or fabrication of motor mounting Regards Clive Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 21, 2015 Hi Clive, I wasn't planning on going as the international show is the week after and a long run also. However that's a straight forward run down the A14 so it's a possible, I'll decide on the day, if it's a real sunny day forcast then hopefully I'll make it. :-) Quote Share this post Link to post Share on other sites
ramjet 862 Report post Posted March 21, 2015 Said it before and I'll say it again, I really like the look of Elites. I'd have one if I could, but I have never seen one. Going to be great finished Charlie. 1 Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 21, 2015 Cheers ramjet. Just been making a small modification which will help improve everyday driving, the windscreen wiper. So the original has a horrible pin and hole fitting which is so fiddly it just a pain in the butt. So got a couple of modern hook fitting wipers and combined the two, my old one to maintain the wiperbox fitting and the new one to have the hook end. Well worth the modification as it looks better and I can add a flat aero blade now with ease. Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 22, 2015 This is a neat modification. It is one easy to overlook. I am not at this stage as yet, changing the wheel box and drive cable is challenging me at the moment. It is difficult to believe how much has to be removed to get at it. Or am I tackling it in the wrong way? Quote Share this post Link to post Share on other sites
clivef38 152 Report post Posted March 22, 2015 Hi Adrian. They started with wheel box and built the car around it. 2 Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 22, 2015 Hi Adrian. They started with wheel box and built the car around it. Someone else made this comment to me recently. Pain of a job taking out the dash and all those damn wires to label. I have a new old type Mini wheel box I hope this is the correct one! Quote Share this post Link to post Share on other sites
Denis247 24 Report post Posted March 22, 2015 (edited) Someone else made this comment to me recently. Pain of a job taking out the dash and all those damn wires to label. I have a new old type Mini wheel box I hope this is the correct one! For a job as involved as this, I wouldn't "hope". Did you try running on the unused section of the wheel 1st? Edited March 22, 2015 by Denis247 Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 22, 2015 On the esprit it's fairly straight forward if you are able to extend your arms around the doors (picture: mister fantastic extended rubber arms), got a mate to help in the end that was definitely a two man job. The elite I wouldn't know, however if it were me I'd remove just the center switch panel first to get a good visual of what lies ahead. Have a look back through my pages, there's a photo of all the dash removed, I'm sure that could help. Good luck! Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 23, 2015 For a job as involved as this, I wouldn't "hope". Did you try running on the unused section of the wheel 1st? I am 3/4 the way through removing the dash so have not yet removed the wheel box to investigate where the wear has taken place. Strangely I still can not see it. More dismantling I presume. Quote Share this post Link to post Share on other sites
Denis247 24 Report post Posted March 23, 2015 (edited) It's a right b*gger of a job, but as you're 3/4 through I'd persevere. I've even heard the story of people cutting out a section of bodywork near the wheelbox to access it, rather than dismantling the dash/heater etc. Using the "unused" section of the wheelbox is a good temp 'fix', coupled with a new rack-cable, cheap & easy to do. This is what I would do 1st if there was too much slop. I think you'll find the wheelbox is not the same as a mini, the diameter of the bit where the arm fixes is one point, but also the Lotus box is designed for 1 wiper arm to sweep over a larger area. These have a larger wheel in the box, but there are also larger wheelboxes around that have the wrong size o/p, so I'd get the proper one from Lotus spares. Edited June 6, 2015 by ramjet Quote Share this post Link to post Share on other sites
CharlieCroker 342 Report post Posted March 23, 2015 If you look at this photo even with the entire dash out it is still not obvious how you access the wiper box. To the left hand side you can see the wiper motor, to my eye it looks like the box is behind the heater matrix or somewhere about there. You all know what I would do, cut an access panel and have done. Quote Share this post Link to post Share on other sites
Denis247 24 Report post Posted March 23, 2015 As I said above, cutting a section of bodywork used to be the bodge a few people have used in the past to do this job, I took the entire heater out when I first had problems years ago, and if you do, take the opportunity to check the heater fans, both how they work and their mounting .. it's another not-so-easy job to do later, one of mine knocks a bit in the housing on a bumpy corner, very annoying. 1 Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 25, 2015 What I considered would be a simple job of changing a wiper wheel box is becoming a bit of a nightmare. I take the point of checking the heater fans, a good idea. At the same time I will be cleaning up the earth connections I can see. 1 Quote Share this post Link to post Share on other sites
pbharcourt 181 1 Vehicles Report post Posted March 25, 2015 (edited) I know everybody says dash off and heaterbox out to remove the wiper wheelbox but i removed mine and refitted it without doing that or cutting a hole. Not sure if this will work for everybody but give it a try! I removed the wiper arm, undid the wiper spindle nut, then in the car removed the wiper motor mount and undid the gland nut on the wiper drive tube and the electrical connections. Then pulled the motor away with drive spring pulling out of the tube and put it on the bench to overhaul. This left the drive tube and spindle box,i then pushed the spindle box into the space behind the heater and pulled it out with the tube, its tight but does go. Putting it back requires a bit of fishing about but again wasnt a problem. Edited March 25, 2015 by pbharcourt 2 Quote Share this post Link to post Share on other sites
dixi4uk 65 Report post Posted March 25, 2015 Now this is the advice I require. I had wondered along these lines and possibly attaching a wire or piece of string to the wheel box wiper attachment area to help replacement.However the easiest way of detatching the drive from the motor is to remove the cover on the motor and remove the crank held by a circlip. The tubing assembly then just slips out. Either way still a good idea. Many thanks for that. Quote Share this post Link to post Share on other sites
