free hit
counters
Time to start explaining - Page 46 - Esprit 'Project & Restoration' Room - The Lotus Forums - Lotus Community Partner #ForTheOwners Jump to content


IGNORED

Time to start explaining


Recommended Posts

  • Gold FFM

Pipes now in the garage - bacon and egg roll eaten - wife jobs done

37456E63-808C-49CA-9D56-9AAC82955902.jpeg.9510d6e72cb81684034d066d3ab1d081.jpeg

driveshaft cv boot replaced - courtesy of my mate Tracey whom has this contraption you put on an air line - boil the boot in some water and hey presto - stretches over E401797B-2C32-40B7-AA64-2219F0BB8C20.jpeg.0db0f0936ae5d7b784787edc8d3b0756.jpeg

my buddy had bell mouthed the pipes in the workshop - and gave me some clear instructions on how to do the next bit 159C6825-33EA-4D12-B04C-19BD0EA90FD8.jpeg.c3de6f0fb11eba078ba7c8cc5753ad04.jpeg649FA45F-5C6E-4334-AA77-9CAFC9EEDC8D.jpeg.8f87a6155341b3672bdf21e722baab88.jpeg

and normally I’d never let me near a hammer for anything critical - but well - after some top tips and instructions I’m pretty chuffed

 

9CC41386-91FD-4378-81AD-A94DDF34F27B.jpeg.f206cc48adb6a0d223af393f13891380.jpeg

next - pipe 2

Only here once

Link to comment
Share on other sites


Upgrade today to remove Google ads and support TLF.

Don't forget to replicate the subtle curve in the long section of the hockey stick coolant pipes to clear the gearshift master unit. Only a Muppet would fit them straight and have to remove and refit them. Ask me how I know...

  • Haha 1

Not worth starting anything now...🍺

Link to comment
Share on other sites

  • Gold FFM

Gearstick unit is all fitted back in - my hammering skills today have been very good indeed. I will go and have another wobble of my stick.

 

yup @eeyoreish I can confirm my stick wobbles - and wobbles all around 

Edited by Barrykearley
  • Like 1

Only here once

Link to comment
Share on other sites

Well done Barry !

  • Thanks 1

1996 Esprit V8, 1998 Esprit V8 GT, 1999 Esprit S350 #002 (Esprit GT1 replica project), 1996 Esprit V8 GT1 (chassis 114-001), 1992 Lotus Omega (927E), 1999 Esprit V8SE, 1999 Esprit S350 #032, 1995 Esprit S4s, 1999 Esprit V8 GT (ex-5th Gear project), 1999 Esprit V8SE ('02 rear)

1999 S350 #002 Esprit GT1 replica

Link to comment
Share on other sites

  • Gold FFM

This covid lockdown does have its advantages. I’m trying to do it in smaller work chunks as I simply haven’t got the focus id normally have. 
 

ive ordered more bits this afternoon for the cold air intake. Some nice stainless plate is coming from my local source to fit where the old airfilter went for the water header tank and catch can (Cheers for hiding that when it came Danny 😂) to be fitted to. 

  • Like 1

Only here once

Link to comment
Share on other sites

  • Gold FFM

Body bolted on. Front mounts to be shimmed yet - but I’ve now found the shims - so they are still to be tightened. Pedal box was not fun to refit - but it’s on.


fans wired, all front pipes fitted, tank crossover pipe, air con pipes, handbrake cable, one pas pipe (need to do the feed pipe). Clutch bled up. Brake servo to be piped up next - just need to make a small bracket to raise the bias valve slightly. I shall leave that until tomorrow.

so the car now goes up and down on the ramp with less tentacles dragging 😂

 

Only here once

Link to comment
Share on other sites

  • Gold FFM

Oil and coolant ordered this morning. Plate collected to mount header tank where the old air filter unit was. Brake unions made off. 
 

just having a brew and I’ll connect up the wiring in the engine bay and start looking at the header tank location. 

  • Like 1

Only here once

Link to comment
Share on other sites

  • Gold FFM

Going through the exact same issue with the seats in mine at the moment.

Why are you moving the coolant tanks and what are you doing with the air filter now?

Norfolk Mustard S4s #1 :)

Link to comment
Share on other sites

  • Gold FFM

Ahh bollocks I knew something went there :wallbash:

 

all will be revealed though - involves some silicon hose, some reducers, a hole saw and a nice carbon cold air intake unit. I simply am not willing to refit that poxy elephants trunk.

 

seats are easy enough to do - thin cutting disc and slot along the bolt heads and weld - then knock out with a hammer. Spot weld new ones in situ. This time I only needed to do 1. 

Only here once

Link to comment
Share on other sites

  • Gold FFM

Boot lid fitted today, all the wiring loom routed and connected, vac pump relocated, spare solenoids cabletied up out the way by the ecu. Just needing oil, coolant and one reducer pipe now.

  • Like 1

Only here once

Link to comment
Share on other sites

1 hour ago, Barrykearley said:

Oil arrived today - I finished work mid afternoon. Came home had grub, a game of scrabble with the kids

OK two questions

1. Did you win?

2. Did you apply the Steptoe and Son rules?

:lol:

Link to comment
Share on other sites

  • Gold FFM

No - my bastard son had a S on his rack at the end of the bag of letters and snuck in a word off a word. 

Now I’m really intrigued - what’s the steptoe and son rules ?

Only here once

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...